How to Make Renewable Energy from Water

One prospective source of renewable energy is hydrogen gas produced from water with the aid of sunlight. Researchers at Linköping University (LiU) in Sweden have developed a material, nanoporous cubic silicon carbide, that exhibits promising properties to capture solar energy and split water for hydrogen gas production.

Cubic silicon carbide immersed in water

New sustainable energy systems are needed to meet global energy and environmental challenges, such as increasing carbon dioxide emissions and climate change”, says Jianwu Sun, senior lecturer in the Department of Physics, Chemistry and Biology at Linköping University, who has led the new study that has been published in the journal ACS Nano.

Hydrogen has an energy density three times that of petrol. It can be used to generate electricity using a fuel cell, and hydrogen-fuelled cars are already commercially available. When hydrogen gas is used to produce energy, the only product formed is pure water. In contrast, however, carbon dioxide is created when the hydrogen is produced, since the most commonly used technology used today depends on fossil fuels for the process. Thus, 9-12 tonnes of carbon dioxide are emitted when one tonne of’ hydrogen gas is produced.

Producing hydrogen gas by splitting water molecules with the aid of solar energy is a sustainable approach that could give hydrogen gas using renewable sources without leading to carbon dioxide emissions. A major advantage of this method is the possibility to convert solar energy to fuel that can be stored. “Conventional solar cells produce energy during the daytime, and the energy must either be used immediately, or stored in, for example, batteries. Hydrogen is a promising source of energy that can be stored and transported in the same way as traditional fuels such as petrol and diesel”, says Jianwu Sun.

It is not, however, an easy task to split water using the energy in sunlight to give hydrogen gas. For this to succeed, it is necessary to find cost-efficient materials that have the right properties for the reaction in which water (H2O) is split into hydrogen (H2) and oxygen (O2) through photo-electrolysis. The energy in sunlight that can be used to split water is mostly in the form of ultraviolet radiation and visible light. Therefore, a material is required that can efficiently absorb such radiation to create charges that can be separated and have enough energy to split the water molecules into hydrogen and oxygen gases. Most materials that have been investigated until now are either inefficient in the way they use the energy of visible sunlight (titanium dioxide, TiO2, for example, absorbs only ultraviolet sunlight), or do not have the properties needed to split water to hydrogen gas (for instance, silicon, Si).

Jianwu Sun’s research group has investigated cubic silicon carbide, 3C-SiC. The scientists have produced a form of cubic silicon carbide that has many extremely small pores. The material, which they call nanoporous 3C-SiC, has promising properties that suggest it can be used to produce hydrogen gas from water using sunlight. The present study has been published in the journal ACS Nano, and in it the researchers show that this new porous material can efficiently trap and harvest ultraviolet and most of the visible sunlight. Furthermore, the porous structure promotes the separation of charges that have the required energy, while the small pores give a larger active surface area. This enhances charge transfer and increases the number of reaction sites, thus further boosting the water splitting efficiency.

The main result we have shown is that nanoporous cubic silicon carbide has a higher charge-separation efficiency, which makes the splitting of water to hydrogen much better than when using planar silicon carbide”, says Jianwu Sun.

Source: https://liu.se/

New Cathode Triples the Energy Storage of Lithium-Ion Batteries

As the demand for smartphones, electric vehicles, and renewable energy continues to rise, scientists are searching for ways to improve lithium-ion batteries—the most common type of battery found in home electronics and a promising solution for grid-scale energy storage. Increasing the energy density of lithium-ion batteries could facilitate the development of advanced technologies with long-lasting batteries, as well as the widespread use of wind and solar energy. Now, researchers have made significant progress toward achieving that goal. A collaboration led by scientists at the University of Maryland (UMD), the U.S. Department of Energy’s (DOE) Brookhaven National Laboratory, and the U.S. Army Research Lab have developed and studied a new cathode material that could triple the energy density of lithium-ion battery electrodes

Lithium-ion batteries consist of an anode and a cathode,” said Xiulin Fan, a scientist at UMD and one of the lead authors of the paper. “Compared to the large capacity of the commercial graphite anodes used in lithium-ion batteries, the capacity of the cathodes is far more limited. Cathode materials are always the bottleneck for further improving the energy density of lithium-ion batteries.

Scientists at UMD synthesized a new cathode material, a modified and engineered form of iron trifluoride (FeF3), which is composed of cost-effective and environmentally benign elements—iron and fluorine. Researchers have been interested in using chemical compounds like FeF3 in lithium-ion batteries because they offer inherently higher capacities than traditional cathode materials.

The materials normally used in lithium-ion batteries are based on intercalation chemistry,” said Enyuan Hu, a chemist at Brookhaven and one of the lead authors of the paper. “This type of chemical reaction is very efficient; however, it only transfers a single electron, so the cathode capacity is limited. Some compounds like FeF3 are capable of transferring multiple electrons through a more complex reaction mechanism, called a conversion reaction.

The findings are published in Nature Communications.

Source: https://www.bnl.gov/